MAPCO Oil Filter (64307)

MAPCO Oil Filter (64307)

The MAPCO Oil Filter 64307 is a high‑performance filtration solution designed to protect the engine of a wide range of vehicles. Engine oil is essential for lubricating moving parts, reducing friction, and preventing wear. Over time, contaminants such as metal shavings, dirt, and combustion by‑products accumulate in the oil. The MAPCO Oil Filter 64307 captures these particles, ensuring that only clean oil circulates through the engine.

Key Features

• Advanced Filtration Media: Utilizes a multi‑layer filtration system that traps particles as small as 0.5 microns, providing superior protection compared to standard filters.
• Durable Construction: Made from high‑quality polypropylene housing and reinforced with a metal frame, the filter resists deformation under pressure and temperature extremes.
• Wide Compatibility: Suitable for engines in OPEL, FORD, FIAT, GRANDLAND X (A18), FOCUS II Schrägheck, FOCUS III, and many other models across multiple manufacturers.
• Easy Installation: Features a standard 69 mm diameter mounting flange that fits most OEM and aftermarket housings without modification.
• Long‑Lasting Performance: Designed to maintain optimal flow rates for extended periods, reducing the need for frequent oil changes in high‑usage conditions.

Applications Across Vehicle Brands

The MAPCO Oil Filter 64307 is engineered to meet the demands of a broad spectrum of vehicles. Below are some representative applications:

• OPEL – Models such as the Grandland X (A18), Focus II Schrägheck, and Focus III Turnier.
• FORD – Including the Transit Pritsche/Fahrgestell and various Kuga generations.
• FIAT – Compatible with standard engine configurations in many Fiat models.
• PEUGEOT – Works with the 207, 307, 5008, 3008, 208, Boxer, Ranch, Bipper, 508, 301, 206, Expert, 308, 4007, 1007, 407.
• CITROËN – Fits the Berlingo C Crosser - Elysee C2 C3 C4 C5 lineup.
• JAGUAR, MITSUBISHI, LAND ROVER, TOYOTA, VOLVO, BMW, and others – Many models across these brands are supported due to the filter’s universal design.

Installation Guide

Installing the MAPCO Oil Filter 64307 is straightforward for technicians familiar with standard oil filter replacement procedures. Follow these steps:

1. Prepare the Vehicle: Raise the vehicle and secure it on jack stands. Drain the engine oil into a suitable container.
2. Remove Old Filter: Use an oil filter wrench to loosen and remove the existing filter. Be careful of residual oil.
3. Clean the Mounting Surface: Wipe the filter housing area with a clean rag to ensure proper sealing.
4. Apply Sealant (Optional): Some technicians apply a thin layer of engine oil on the rubber gasket for an extra seal; however, the MAPCO filter’s gasket is designed to create a reliable seal without additional adhesive.
5. Install New Filter: Screw the MAPCO Oil Filter 64307 onto the housing by hand until snug. Tighten an additional half‑turn with the wrench, ensuring not to overtighten and damage the gasket.
6. Refill Engine Oil: Refill the engine with the recommended oil type and quantity as specified in the vehicle’s owner manual.
7. Check for Leaks: Start the engine and inspect the filter area for any signs of leakage. Tighten further if necessary.

Performance Benefits

The MAPCO Oil Filter 64307 delivers several tangible advantages to vehicle owners and mechanics alike:

• Engine Longevity: By removing contaminants, the filter reduces wear on bearings, pistons, and camshafts.
• Fuel Efficiency: Clean oil maintains optimal viscosity, allowing the engine to run more efficiently and potentially improving mileage.
• Reduced Maintenance Costs: A robust filter can extend intervals between oil changes in certain driving conditions, saving time and resources.
• Consistent Oil Flow: The filter’s design maintains adequate flow rates even under high‑temperature operation, preventing pressure drops that could affect engine performance.