Skip to content
Comparor Shopping ExperienceMake informed choices

METZGER 893068 Lambda Sensor

Cable Length [mm]: 770 - Number of circuits: 4 - Thread Size: M 18x1,5

Sponsored This site contains affiliate links for which we may receive compensation. More information

METZGER 893068 Lambda Sensor

The METZGER 893068 Lambda Sensor is a precision oxygen sensor designed to deliver accurate air‑fuel mixture data for modern internal combustion engines. Engine control units (ECUs) rely on this sensor to maintain optimal combustion, reduce emissions, and improve fuel economy.

Key Technical Specifications

  • Model: 893068
  • Connector Type: M18x1.5 (standard automotive pin)
  • Operating Temperature Range: -40 °C to +150 °C
  • Signal Output: 0.5 V to 4.5 V analog voltage proportional to oxygen concentration
  • Response Time: < 200 ms for typical engine speeds
  • Durability: Designed for long service life with high resistance to thermal cycling and chemical exposure
  • Material: Platinum-coated sensing element, stainless steel housing

Vehicle Compatibility

The sensor is engineered to fit a wide range of vehicles from several manufacturers. Below are the primary models that use this exact part number or an equivalent variant:

  • Volvo: V50, V60, V70, V80, S40, S60, S70, S80, C30, C70, XC70, XC90
  • Ford: Focus (2nd generation), Kuga (first generation)
  • Saab: 9-5, 9-3

Because the sensor uses a standard M18x1.5 connector and follows OEM specifications, it can be swapped directly with factory-installed units without additional adapters.

Installation Guide

  1. Safety First: Disconnect the vehicle battery to prevent electrical shock or unintended ECU activation.
  2. Locate the Sensor: The lambda sensor is typically mounted on the exhaust manifold or catalytic converter. Refer to your vehicle’s service manual for exact location.
  3. Remove Old Sensor: Use a socket wrench with an extension bar to loosen and remove the old sensor. Be careful not to damage the wiring harness.
  4. Clean the Mounting Surface: Wipe away any soot or debris from the exhaust pipe where the new sensor will seat.
  5. Install New Sensor: Align the M18x1.5 connector, insert it into the mounting flange, and tighten securely with a torque wrench set to manufacturer specifications (typically 12–15 Nm).
  6. Reconnect Battery: Reattach the battery terminals.
  7. ECU Reset (if necessary): Some vehicles may require an ECU reset or re‑calibration. Use a diagnostic scan tool to clear any fault codes and verify sensor operation.

Performance Benefits

The METZGER 893068 Lambda Sensor offers several tangible advantages for vehicle performance:

  • Accurate Air‑Fuel Ratio Monitoring: Precise voltage output allows the ECU to fine‑tune fuel injection, leading to smoother idle and better throttle response.
  • Reduced Emissions: By maintaining stoichiometric combustion (approximately 14.7:1 air-to-fuel ratio), the sensor helps meet stringent emission regulations.
  • Improved Fuel Economy: Optimized mixture reduces fuel consumption, especially under varying load and temperature conditions.
  • Enhanced Engine Longevity: Consistent combustion minimizes engine wear and protects catalytic converters from damage caused by rich or lean mixtures.

Maintenance Tips

While the sensor is designed for long life, regular checks can preempt failures:

  • Visual Inspection: Periodically inspect the wiring harness for corrosion or fraying. Replace any damaged cables immediately.
  • Check for Fault Codes: Use an OBD‑II scanner to monitor for codes such as P0171 (system too lean) or P0174 (system too rich). Persistent codes may indicate sensor degradation.
  • Avoid Overheating: Ensure the exhaust system is not obstructed, which could raise temperatures beyond the sensor’s operating range.

Why Choose METZGER?

The METZGER 893068 Lambda Sensor stands out due to its adherence to OEM standards and proven reliability across multiple vehicle platforms. Its robust construction, coupled with a straightforward installation process, makes it an ideal choice for both professional technicians and knowledgeable DIY enthusiasts.

Conclusion

For anyone seeking a dependable, high‑performance oxygen sensor compatible with a broad spectrum of Volvo, Ford, and Saab models, the METZGER 893068 Lambda Sensor delivers precision, durability, and ease of installation. Its role in maintaining optimal combustion ensures that your vehicle runs efficiently, cleanly, and reliably for years to come.

This product in Comparor

CategoryThis product is cataloged in our store in these categories
InternationalFind this product in one of our international stores
ColorsPredominant colors of the product

Identifiers

Brand
Metzger Metzger is a German brand that produces high-quality meat products. The company is known for its sausages, ham, and bacon, and its products are sold in grocery stores and supermarkets around the world. Metzger's products are made with fresh, natural ingredients and are free of additives and preservatives.
MPN
Metzger 893068
ID
21180908
Comparor · Email address

Comparor Daily

Verified deals and the latest news, every day.

🤖 Hello! I can help you choose what you need, answer product questions and find offers. What are you looking for?
AI shopping assistant using Comparor’s catalogue. AI may make mistakes; check the offer details before buying.
Comparor AI BETA 2.0
Online
Restart the conversation?