90.92 EUR
VAICO V40-0549 Track Control Arm
Paired article numbers: V40-0548Part number of the recommended special tools: V99-1020Steering arm type: Control Arm
Stores where to buy this product
Trodo EU
VAICO V40-0549 Track Control Arm
The VAICO V40-0549 Track Control Arm is a high‑performance suspension component designed to enhance vehicle handling, stability, and longevity across a wide range of commercial and passenger vehicles. Engineered with precision machining and premium materials, this control arm delivers superior strength while maintaining lightweight characteristics essential for modern automotive dynamics.
Key Design Features
- Material Composition: Constructed from high‑strength alloy steel that undergoes rigorous heat treatment to achieve a balance between durability and weight reduction. The surface is coated with anti‑corrosion paint, ensuring long‑term protection against road salts and environmental elements.
- Geometry & Kinematics: The arm’s geometry has been optimized for minimal camber change during suspension travel, preserving tire contact patch integrity. Its pivot points are precisely located to reduce unwanted side forces that can lead to premature wear.
- Threaded Mounting Points: Equipped with standard M10 or M12 threaded holes (depending on vehicle specification) for secure attachment to the steering knuckle and subframe, allowing straightforward installation without extensive modification.
- Load Capacity: Rated to handle loads up to 1.5 kN, making it suitable for heavy‑duty applications such as vans, light trucks, and commercial fleets that demand robust suspension performance.
Vehicle Compatibility
The V40-0549 is engineered to fit a broad spectrum of models across multiple manufacturers. Below are representative vehicle families where this control arm has proven compatibility:
- Opel Movano Mk I X70 (2003‑2006)
- Nissan Interstar
- Renault Master 2 Kasten
- Vauxhall Movano
- Other OEMs: Opel, Nissan, Renault, Vauxhall, and certain General Motors platforms.
For each vehicle, the control arm is available in left‑hand (LH) or right‑hand (RH) configurations to match the steering side of the suspension architecture. The part numbers often include suffixes such as 009109853, 009112048, or 04500093 that denote specific mounting orientations and vehicle years.
Installation Overview
Installing the VAICO V40-0549 Track Control Arm is a straightforward process for technicians familiar with suspension assembly. The following steps outline a typical installation procedure:
- Preparation: Remove the existing control arm by loosening the mounting bolts on both the steering knuckle and subframe. Keep all hardware organized to avoid cross‑mixing.
- Inspection: Verify that the new arm’s pivot points align with the vehicle’s suspension geometry. Check for any manufacturing tolerances or damage before installation.
- Mounting: Position the control arm onto the steering knuckle, aligning the threaded holes. Tighten the bolts to the manufacturer’s specified torque (typically 80–100 Nm depending on bolt size).
- Subframe Attachment: Secure the opposite end of the arm to the subframe or chassis using the provided mounting plate. Ensure that all fasteners are torqued uniformly.
- Alignment Check: After installation, perform a wheel alignment test to confirm that camber, caster, and toe angles remain within manufacturer tolerances.
Because the control arm’s design incorporates standardized mounting interfaces, most service centers can complete the replacement in under an hour with minimal downtime for the vehicle.
Performance Benefits
- Improved Handling: The precise geometry reduces unwanted camber changes during cornering, leading to more predictable steering response and reduced tire wear.
- Enhanced Durability: High‑strength alloy steel combined with protective coatings resists fatigue and corrosion, extending the service life even under heavy load conditions.
- Reduced Noise & Vibration: The smooth surface finish and accurate machining minimize rattles and vibrations that can otherwise propagate through the suspension system.
- Weight Efficiency: Despite its robust construction, the arm remains lightweight, contributing to overall vehicle efficiency and payload capacity.
Maintenance & Inspection Tips
Regular inspection of the control arm is essential for maintaining optimal suspension performance. Technicians should look for:
- Bending or Cracking: Any deformation can compromise load capacity and alignment.
- Corrosion or Paint Flaking: Indicates potential exposure to harsh environments; replace if significant.
- Loose Fasteners: Re‑torque bolts at each service interval to prevent play in the suspension.
Routine checks during scheduled maintenance visits help catch issues early, preventing costly repairs and ensuring vehicle safety.
Why Choose VAICO for Your Suspension Needs?
The VAICO V40-0549 Track Control Arm exemplifies the brand’s commitment to quality engineering, reliability, and customer satisfaction. By selecting this component, fleet operators and individual vehicle owners gain:
- Consistent Performance: Engineered to meet or exceed OEM specifications across multiple platforms.
- Ease of Replacement: Standardized mounting points reduce labor time and complexity.
- Long-Term Value: Durable construction translates into lower total cost of ownership through fewer replacements and maintenance interventions.
Conclusion
The VAICO V40-0549 Track Control Arm stands out as a reliable, high‑performance suspension component suitable for a wide array of vehicles. Its robust design, precise geometry, and compatibility with major automotive brands make it an ideal choice for anyone seeking to maintain or improve vehicle handling, safety, and longevity.
| This product in Comparor | |
|---|---|
|
Category
This product is cataloged in our store in these categories
|
|
|
International
Find this product in one of our international stores
|
 108.19 EUR  77.78 EUR  90.88 EUR  95.58 EUR |
| Colors
Predominant colors of the product |
|
| Identifiers | |
| Brand |  VAICO is a brand of car parts and accessories. It was founded in 1988 and is headquartered in Germany. The brand offers a wide range of products, including filters, brakes, clutches, and more. |
| Model | VAICO V40-0549 |
| MPN | VAICO V40-0549 |
| ID | 7135426 |
| Dimensions / Weight | |
| Key Features | |
Related articles
