Two flute carbide TCT tips for clean, professional finish on timber lippings, plastic laminates and veneers. - 12.7mm diameter X 25.4mm cutting depth bottom bearing guided trimmer. Accurately and cleanly flush trims laminate and veneer work. - 1/4in sha
Ideal for trimming and profiling timber, man-made board Designed with micrograin tungsten carbide tips Cutter is PTFE coated, indicated by distinctive black colouring
For trimming and profiling timber man-made board. Features 2mm micrograin Tungsten Carbide tips, for cutting the most abrasive materials to give extra long life.PTFE coated, indicated by distinctive black colouring.Can be used on hardwood
Fits directly to Trend T3,T4,T5,T5 MK2, T9,T10 and T11, can also be used with non Trend routers with the same base configuration. - Will also fit other makes of Router when used with GB/5, GB/PLATE or UNIBASE Sub-base. - Guide bush screws GB/01 required f
Trend's self-clamping guide router base plate is designed for edge clamp guides, offering precise and easy alignment. The clear base plate allows you to see your work piece while cutting.
Trend's self-clamping guide router base plate is designed for edge clamp guides, offering precise and easy alignment. The clear base plate allows you to see your work piece while cutting.
The Trend CRAFTPRO Intumescent Strip Router Cutter is a 1/4 inch shank tool designed for creating recesses in intumescent strips. This 24mm x 10mm cutting head provides precise and efficient cuts, making it ideal for fire-stopping applications.
6.3mm diameter X 25mm cutting length bearing guided trimmer for bringing decorative laminates and veneers flush to an edge or for templating work. - Bearing guide can be used with templates with 25mm cut length suitable for trimming work on standard sheet
9.5mm diameter x 25mm cutting depth bearing guided profiling cutter, perfect for templating and trimming work in timber, laminates and wood based materials. - Shank mounted bearing allows good vision of the template for easy and accurate following when ha
An ideal cutter for newel posts and caps for stairs, supplied with one 9.5mm bearing. - For use in fixed head mode only due to large cutter diameter, smaller bearing available for increased chamfer width. - Cutter specification :- Diameter 50mm, Cut lengt
Trend's CRAFTPRO Bearing Guided Housing Router Cutter is a precision tool with a diameter of 19.1mm and shank size of 11.1mm, ideal for use with a 1/4 inch collet.
Trend's CRAFTPRO Bearing Guided Housing Router Cutter is a precision tool with a diameter of 19.1mm and shank size of 11.1mm, ideal for use with a 1/4 inch collet.
The product is a universal subbase designed to fit most routers, featuring integrated guide bushings and adjustable pins for precision control.
The product is a universal subbase designed to fit most routers, featuring integrated guide bushings and adjustable pins for precision control.
Trend's biscuit joiner is a precision tool for creating strong and accurate wood joints, with a 4mm shank size and a 37.2mm cutting diameter. It features a bearing-guided cutter set and a 1/4 TCT blade for smooth cuts.
The Trend Kitchen Worktop Jig Offset Scriber is a precision tool designed for accurate worktop installation, helping you achieve perfectly aligned edges.
Dimension R /B: 12.7 mm Dimension D: 86 mm Dimension C: 12.7mm
Attractive edge moulds.A full corner bead can be produced by making a second pass at 90 degrees.Craft pro range tungsten carbide tipped router cutter bits
Ideal for trimming and bevelling timber, lippings and plastic laminate edges Cutter is PTFE coated, indicated by distinctive black colouring Designed with micrograin tungsten carbide tips
Attractive edge moulds.A full corner bead can be produced by making a second pass at 90 degrees.Craft pro range tungsten carbide tipped router cutter bits
The Trend Craft C076X1/4TC Pro 1/4in shank bearing-guided round over router cutter features a 6.3mm radius and two flute carbide tips for precision cutting.
50mm cutting depth for replicating thicker components with templates; ideal for heavier joinery and furniture work.Bottom bearing guide for following an edge to trim laminates and veneers for a professional finish.Two flute carbide TCT ti
Two flute carbide TCT tips for cleaner cutting edges and fast clearance of waste in all timber and timber based materials.1/8in imperial radius for matched replication. Leaves perfect fine round over detail for a contemporary eased edge profile
The Trend Butt Hinge Router Template is a precision tool for creating accurate and consistent cuts when installing butt hinges on doors. Designed for both 75mm and 100mm hinges, this template ensures professional results with minimal effort.
Two flute carbide TCT tips for clean, professional finish on timber lippings, plastic laminates and veneers. - 12.7mm diameter X 9.5mm cutting depth shank mounted bearing guided trimmer. Ideally suited to flush trim laminate and veneer work. - 1/4in sha
MUST-HAVE FOR ANY ROUTER: The 30mm guide bush is ideal for use with Trend Trade Jigs and for general templating or jig work - PRECISION WORK: Essential for pinpoint accuracy when using jigs - SHORT 6MM SPIGOT LENGTH: Ideal for user-made templates with thi
Trend - Shank mounted bearing guided door leading edge - Trade Router Cutters
For trimming and bevelling timber, lippings and plastic laminate edges or any shaping applications. - Self-guiding trimmer with bearings mounted on end of cutter. - For trimming plastic or plywood overlay. - For copy profiling, use the bearing to follow a
Fits directly to Trend T3,T4,T5,T5 MK2, T9,T10 and T11, can also be used with non Trend routers with the same base configuration. - Will also fit other makes of Router when used with GB/5, GB/PLATE or UNIBASE Sub-base. - Guide bush screws GB/01 required f
For trimming and bevelling timber, lippings and plastic laminate edges. - Features 2mm micrograin Tungsten Carbide tips, for cutting the most abrasive materials to give extra long life. - PTFE coated, indicated by distinctive black colouring. - Can be use
For 4.0mm thick strip. For 15.0mm wide intumescent strip. - Trade range extra long tungsten carbide tipped router cutter bits with PTFE coating
Trend Guide Bush for 27mm routers: Enhance precision & versatility with this essential tool. Perfect for various applications, ensuring smooth operation & accurate results. Suitable for use with Trend Routers & other compatible models.
The Trend TR33X14TC is a bearing-guided chamfer router cutter with a diameter of 31.8mm and a shank size of 1/4 inch, suitable for cutting angles of up to 45 degrees.
3 degree undercut router bit with shank mounted bearing guide for routing the leading edge on doors to allow a tight fit against jamb. - Suitable for use in medium - heavy duty Routers with a minimum wattage of 1500 watts. - Cutter specification :- diamet
Dimension R: 7 mm - Dimension D: 31.9 mm - Dimension d: 28.6 mm - Dimension B: 16 mm
Requires an arbor Ref. 33/60 and suitable diameter bearing to govern depth of cut. - All slotters are precision made in TCT grade for long life when cutting the most abrasive materials - Dimensions: D=36 mm Kerf=3.0 mm No. of Teeth=2 Grade: TCT Diameter M
