ABS 200008 Wheel Bearing Kit

ABS 200008 Wheel Bearing Kit

The ABS 200008 Wheel Bearing Kit is a comprehensive replacement set designed to restore optimal performance and safety to the rear axle of selected Ford and Mazda models. This kit includes every component required for a complete bearing assembly, ensuring that technicians can perform a flawless installation without needing additional parts.

Key Components Included

• Front Wheel Bearing Assembly – Precision-machined steel housing and bearing pair engineered to match OEM specifications.
• Rear Wheel Bearing Assembly – Dual-bearing set with high‑strength steel housings, calibrated for maximum load capacity.
• Seals and Gaskets – High‑temperature resistant seals that prevent lubricant leakage and protect against contaminants.
• Fasteners and Hardware – All necessary bolts, nuts, washers, and locking devices to secure the bearing assembly firmly in place.
• Installation Instructions – Step‑by‑step guide with torque specifications and safety precautions.

Compatibility Overview

The kit is engineered for a wide range of Ford and Mazda vehicles, including but not limited to:

• Ford Fiesta Mk5 (JH1, JD1, JH3, JD3)
• Ford Focus (DAW, DBW) and Fusion (JU)
• Mazda 2 (Dnw), Mazda Demio, Ikon V, Street Ka, Puma
• Other models sharing the same rear axle architecture as listed above.

Each component is stamped with the part number 200008, guaranteeing exact fitment across all supported vehicles. The kit’s design adheres to original equipment manufacturer (OEM) tolerances, ensuring that performance and durability match factory standards.

Engineering Excellence

The ABS 200008 Wheel Bearing Kit incorporates advanced materials and manufacturing techniques:

• High‑Grade Steel Housing – Offers superior wear resistance and structural integrity under high torque conditions.
• Precision Ball Bearings – Manufactured to tight tolerances, providing smooth rotation and minimal friction.
• Corrosion‑Resistant Coatings – Protects against rust and extends the service life of each component.
• Thermal Stability – Maintains performance across a wide temperature range, from cold starts to high‑speed operation.

Installation Process

The kit’s installation procedure is streamlined for both professional mechanics and knowledgeable DIY enthusiasts. The following steps outline the typical workflow:

1. Vehicle Preparation – Secure the vehicle on a lift or jack stands, remove the wheel, and disconnect the brake caliper.
2. Bearing Removal – Use a bearing puller to extract the old bearings from the hub assembly. Dispose of worn seals properly.
3. Cleaning – Thoroughly clean the hub housing and surrounding area with solvent to remove grease, dirt, and debris.
4. Seal Installation – Apply new seals to the bearing housings, ensuring they sit flush against the mounting surface.
5. Bearing Assembly – Insert the new bearings into the housing, aligning them with the hub flange. Use a torque wrench to secure all fasteners to the specified values.
6. Reassembly – Reinstall the brake caliper, wheel, and any ancillary components. Verify that all bolts are tightened to specification.
7. Test Drive – Conduct a short test drive to confirm smooth operation and absence of abnormal noises or vibrations.

All torque values and detailed instructions are provided in the included manual, ensuring compliance with safety standards and optimal performance.

Benefits of Replacing with ABS 200008 Kit

• Enhanced Safety – Reliable bearings reduce the risk of wheel lockup or bearing failure during braking and acceleration.
• Improved Handling – Smooth bearing operation contributes to precise steering response and vehicle stability.
• Longevity – High‑quality materials and OEM design extend the lifespan of the rear axle assembly.
• Consistent Performance – Matching OEM specifications ensures that handling characteristics remain unchanged after replacement.
• Cost Efficiency – A complete kit eliminates the need for multiple separate purchases, reducing overall labor and material costs.

Maintenance Tips

Even with a new bearing set, regular maintenance can further prolong component life:

• Inspect wheel bearings annually for signs of wear or damage.
• Keep the hub area clean and free from debris that could compromise seal integrity.
• Use high‑quality lubricants recommended by the manufacturer during any future bearing service.
• Avoid overloading the vehicle beyond its rated capacity, as excessive load accelerates bearing wear.

Conclusion

The ABS 200008 Wheel Bearing Kit delivers a complete, OEM‑grade solution for rear axle bearing replacement on a broad spectrum of Ford and Mazda vehicles. Its meticulous engineering, comprehensive component set, and clear installation guidance make it the preferred choice for professionals seeking reliability and performance that match factory standards.