MAHLE OX 1075D Oil Filter

MAHLE OX 1075D Oil Filter

The MAHLE OX 1075D Oil Filter is a high‑performance filtration solution engineered to meet the demanding requirements of modern powertrains. Designed with precision and built for durability, this filter delivers superior protection for engine oil systems in a wide range of vehicles, ensuring optimal performance, longevity, and compliance with stringent emission standards.

Key Design Features

• Advanced Filter Media: Utilizes a multi‑layered filtration matrix that captures particles as small as 0.5 µm, effectively removing contaminants while maintaining low pressure drop for efficient oil flow.
• Robust Construction: Constructed from high‑strength polypropylene housing with reinforced rubber seals to resist cracking and maintain integrity under extreme temperatures and pressures.
• Optimized Flow Dynamics: Engineered geometry reduces turbulence, ensuring consistent oil delivery and minimizing the risk of cavitation or filter blockage during transient operating conditions.
• Extended Service Life: Designed to withstand prolonged operation in high‑load engines, offering a service interval that aligns with manufacturer recommendations for many Volvo, Polestar, Mercedes‑Benz, and C‑Class models.

Compatibility Overview

The OX 1075D filter is specifically tailored to fit a broad spectrum of vehicles. Its dimensions—outer diameter 73.5 mm, inner diameter 22 mm, and height approximately 105 mm—make it suitable for:

• Volvo Models: V40, V60, S60, XC90, XC70, XC60, XC40, S80, S90, V70, and various Mk2/Mk3 generations.
• Polestar Series: Polestar 1, Polestar 2, and other high‑performance variants.
• MERCEDES‑Benz & C‑Class: A‑Class (W176), C‑Class Limousine (W205), M‑Klass (W166).

OEM part numbers such as 31321084, 313210840, 31372212, 313722120, 31372214, and 72407210 are all interchangeable with the OX 1075D, ensuring a seamless fit for both original equipment and aftermarket installations.

Installation & Maintenance Guidelines

1. Preparation: Warm the engine to operating temperature to reduce oil viscosity, facilitating easier removal of the old filter.
2. Removal: Use a suitable filter wrench to loosen and carefully detach the existing filter. Dispose of the used filter responsibly.
3. Installation: Apply a thin layer of fresh engine oil onto the rubber seal before inserting the new filter. Tighten by hand until snug, then give an additional quarter turn with the wrench—over‑tightening can damage seals.
4. Post‑Install Check: Inspect for leaks around the mounting surface and verify that the filter is seated correctly. Start the engine and allow it to reach normal operating temperature while monitoring oil pressure gauges.

Performance Benefits

• Enhanced Engine Protection: By trapping fine particulates, the filter prevents abrasive wear on pistons, bearings, and camshafts, thereby extending engine life.
• Improved Fuel Efficiency: Maintaining optimal oil flow reduces friction losses, contributing to better fuel economy.
• Consistent Oil Quality: The filter’s low pressure drop ensures that the oil reaches all critical components at the required rate, preserving lubrication performance even under high‑load conditions.
• Emission Compliance: Clean oil reduces particulate emissions from exhaust systems, aiding compliance with Euro 6 and other stringent environmental regulations.

Quality Assurance & Manufacturing Excellence

The MAHLE OX 1075D Oil Filter is manufactured in a state‑of‑the‑art facility that adheres to ISO 9001 and ISO/TS 16949 quality management standards. Each filter undergoes rigorous testing, including:

• Pressure Drop Test: Ensures the filter meets specified flow characteristics.
• Particle Retention Test: Confirms filtration efficiency for sub‑micron contaminants.
• Durability & Leak Test: Validates seal integrity under simulated operating conditions.

Environmental Considerations

The filter’s design incorporates recyclable materials wherever possible, and the manufacturing process minimizes waste. By extending engine life and reducing oil consumption, the OX 1075D contributes to lower overall environmental impact.

User Experience & Feedback

Owners of vehicles equipped with the MAHLE OX 1075D Oil Filter frequently report:

• Consistent oil pressure readings across all operating temperatures.
• No noticeable changes in engine noise or performance after installation.
• Positive feedback from service technicians regarding ease of installation and reliability during routine maintenance cycles.

Conclusion

The MAHLE OX 1075D Oil Filter stands out as a premium filtration solution that blends advanced engineering, broad compatibility, and proven performance. Whether you are maintaining a Volvo, Polestar, Mercedes‑Benz, or C‑Class vehicle, this filter delivers the protection your engine deserves while supporting efficiency and environmental stewardship.