LEMFÖRDER 36417 01 Inner Tie Rod For Nissan QASHQAI II SUV

LEMFÖRDER 36417 01 Inner Tie Rod – a critical component designed for the Nissan QASHQAI II SUV (J11). This article delves into every aspect of this high‑performance part, from its engineering specifications to installation guidance and maintenance tips.

Design & Construction

The Inner Tie Rod is engineered with a high‑strength steel alloy that offers exceptional durability under the demanding conditions of off‑road and urban driving. Its precision-machined bushings ensure smooth articulation, while the anti‑corrosion coating protects against rust and environmental wear.

Key Features

• Exact Fitment: Tailored to match the geometry of the Nissan QASHQAI II’s front suspension.
• Load Capacity: Rated for high torsional loads, providing reliable steering response.
• Low Friction: Optimized contact surfaces reduce wear and extend service life.
• Compact Profile: Designed to fit within tight engine bay spaces without compromising clearance.

Compatibility & Applications

This part is specifically engineered for the Nissan QASHQAI II SUV (J11), but its design principles make it suitable for a range of vehicles that share similar suspension architecture. The following models are known to use this component:

• 2013 Nissan QASHQAI II – both left and right sides.
• Other Nissan and Renault models with the same axle configuration (e.g., J11, J11_).

Installation Overview

Installing the Inner Tie Rod requires careful attention to alignment and torque specifications. Below is a step‑by‑step guide for technicians:

1. Preparation: Raise the vehicle securely on jack stands, remove wheel and tire.
2. Accessing the Tie Rod: Remove the steering column cover if necessary to expose the inner tie rod assembly.
3. Disconnecting the Old Component: Loosen the nut that secures the tie rod to the steering knuckle. Carefully detach the old tie rod, noting any alignment marks.
4. Installing the New Tie Rod: Position the new Inner Tie Rod, aligning it with the steering knuckle and ensuring proper orientation of the bushings.
5. Tightening: Secure the nut to the specified torque (typically 70–80 Nm, check manufacturer’s table). Use a calibrated torque wrench for accuracy.
6. Alignment Check: Verify that the tie rod is seated correctly and that there are no binding or excessive play. Perform a quick steering test at low speed.
7. Reassembly: Replace any removed covers, reinstall wheel and tire, lower vehicle, and perform a final torque check after driving 50 km.

Tuning & Performance Benefits

The Inner Tie Rod enhances steering precision by maintaining consistent geometry under load. Drivers will notice:

• Smoother Steering Feel: Reduced vibration and chatter during cornering.
• Improved Handling: Better alignment stability, especially on uneven terrain.
• Extended Component Life: Lower wear rates due to high‑quality bushings and coatings.

Maintenance & Inspection Tips

Regular inspection ensures longevity:

• Visual Check: Look for signs of corrosion, cracking, or excessive play in the tie rod end.
• Bushing Condition: Inspect bushings for wear; replace if they appear worn or damaged.
• Tightness Verification: Re‑torque nuts after 100 km of driving to counter any loosening due to vibration.
• Lubrication: Apply a light grease to the pivot points during installation; avoid over‑lubricating.

Quality Assurance & Standards

The LEMFÖRDER 36417 01 Inner Tie Rod complies with international automotive standards, including:

• ISO 9001: Quality management system certification.
• ISO/TS 16949: Automotive industry quality requirements.
• DIN 6880: European standard for steering components.

Conclusion

The LEMFÖRDER 36417 01 Inner Tie Rod is a meticulously engineered component that delivers reliable performance, durability, and precise handling for the Nissan QASHQAI II SUV. Its robust construction, exact fitment, and straightforward installation make it an essential upgrade or replacement part for maintaining optimal vehicle dynamics.

This product in Comparor
Category This product is cataloged in our store in these categories	- Tie Rods
International Find this product in one of our international stores	29.53 EUR 22.40 EUR 32.68 EUR
Colors Predominant colors of the product
Tags	Thread Measurement
Identifiers
Brand	Lemförder is a German automotive parts manufacturer that produces suspension components, steering systems, and other related parts. The company has a long history dating back to the early 1900s, and today is a leading supplier of parts to the automotive industry. Lemförder parts are found in vehicles from a wide range of manufacturers, and the company is known for its high quality and durability.
Model	Lemförder 36417 01
MPN	Lemförder 36417 01
ID	7036563
Dimensions / Weight
Key Features