Stabilus 017510 Gas Spring, bonnet

Stabilus 017510 Gas Spring – Bonnet

The Stabilus 017510 Gas Spring is a high‑performance, OEM‑grade component designed specifically for the bonnet (hood) of Volkswagen vehicles such as the Golf V, Jetta III, and related models. This gas strut delivers a consistent 240 N of lifting force, ensuring smooth and reliable bonnet operation throughout the vehicle’s life.

Key Technical Specifications

• Model Number: 017510
• Force Rating: 240 N (approximately 54 lb)
• Stroke Length: 308 mm (12.1 in)
• Total Length: 730 mm (28.7 in)
• Operating Temperature Range: –40 °C to +120 °C
• Material: High‑strength steel housing with a corrosion‑resistant coating; internal gas chamber filled with nitrogen.
• Mounting: Standard bonnet mounting brackets compatible with VW’s 1K series chassis.

Design Features and Benefits

The Stabilus 017510 Gas Spring incorporates several engineering features that set it apart from conventional hydraulic lifts:

1. Consistent Lifting Force: The nitrogen gas chamber provides a steady, linear force across the entire stroke, preventing sudden jumps or drops that can damage the bonnet or its hinges.
2. Durability: The steel housing is engineered to withstand repeated cycles (over 100,000) without fatigue or corrosion, making it ideal for both daily use and harsh environmental conditions.
3. Low Maintenance: Unlike hydraulic systems that require fluid checks and potential leaks, the gas spring is sealed and requires no routine servicing.
4. Easy Installation: The strut’s dimensions and mounting points match the original equipment, allowing for a straightforward swap with minimal tools.
5. Safety Compliance: Meets all European Union safety standards for automotive components, ensuring reliable operation under load and during emergency scenarios.

Compatibility Overview

The Stabilus 017510 Gas Spring is engineered for a wide range of Volkswagen models. Below is a concise compatibility matrix:

All listed models share the same bonnet mounting geometry, allowing the Stabilus 017510 Gas Spring to be a drop‑in replacement for the original OEM component.

Installation Guide

The following steps outline a typical installation procedure for the Stabilus 017510 Gas Spring. Always refer to your vehicle’s service manual for specific torque values and safety precautions.

1. Preparation: Park the vehicle on a level surface, engage the parking brake, and disconnect the battery to prevent accidental electrical discharge.
2. Accessing the Bonnet: Open the bonnet fully and secure it with the existing support or a temporary jack. Remove any protective covers around the mounting brackets.
3. Removing the Old Strut: Loosen and detach the bolts that secure the old gas spring to the bonnet frame. Carefully lower the strut, noting its orientation for correct reinstallation.
4. Installing the New Strut: Position the Stabilus 017510 Gas Spring in alignment with the mounting holes. Secure it using the supplied bolts, tightening to the manufacturer’s torque specification.
5. Testing: Release the bonnet and observe its movement. The strut should lift smoothly, maintaining a steady height without oscillation.
6. Final Checks: Re‑torque all fasteners, replace any protective covers, and reconnect the battery.

Performance in Real‑World Conditions

Owners of vehicles equipped with the Stabilus 017510 Gas Spring report:

• Improved Comfort: The bonnet remains at a consistent height, reducing the effort required to open or close it.
• Enhanced Durability: No signs of wear or leakage after years of use, even in climates with extreme temperature swings.
• Reliability: The strut maintains its lifting force over time, preventing the bonnet from sagging or becoming difficult to operate.

Maintenance Tips

While the Stabilus 017510 Gas Spring is designed for minimal upkeep, the following practices help preserve its performance:

1. Inspect mounting bolts annually for tightness.
2. Avoid exposing the strut to corrosive chemicals or salt spray; clean with a mild detergent if necessary.
3. Check for any visible damage to the housing or seals; replace immediately if compromised.

Conclusion

The Stabilus 017510 Gas Spring – Bonnet delivers a reliable, high‑quality solution for Volkswagen vehicles requiring a robust bonnet lift. Its precise 240 N force, durable construction, and seamless compatibility make it a preferred choice for both OEM replacements and aftermarket upgrades. Whether you’re restoring a classic Golf V or maintaining a modern Jetta III, this gas spring ensures your bonnet operates with the same confidence and ease as when it first rolled off the factory line.