Electrical installation
Suggestions for Electrical installation
Level Heat gun Hole saw Wire nut Cable lug Cable tie Drill bit Fish tape Cable clip Multimeter Nut driver Wire gauge Cable clamp GFCI tester Screwdriver Stud finder Wire cutter Cable cutter Cable puller Conduit body Hammer drill Tape measure Crimping tool Torque wrench Utility knife Wire stripper Cable stripper Circuit tester Conduit bender Conduit cutter Electrical box Soldering iron Terminal block Voltage tester Wire connector Bosch drill bit Conduit fitting Crimp connector Grounding clamp Milwaukee drill
Compact 3‑pole miniature circuit breaker with a 13 A rating and 6 kA breaking capacity, featuring a C‑type tripping curve for fast fault interruption in low‑voltage installations.
Compact Siemens 5SY6313‑6 miniature circuit breaker offers 13 A rating, 3‑pole operation, Char‑B tripping curve, and 6 kA short‑circuit capacity, ideal for residential or commercial panelboards.
Siemens 5TT4201-0 installation relay for 230VAC with 16A nominal current and one NO contact.
Installation relay with 2 normally open contacts, operating at 230V AC and handling up to 16A current.
Easily join up to eight conductors using the WAGO 2002‑408 insulated jumper bar; its push‑in terminals provide secure, low‑resistance connections and simplify cable routing in tight panels.
Securely connect ground wires up to 6 mm² with this single‑pole, 41A WAGO 2006‑1307 terminal block, featuring a robust 3‑conductor feed‑through design for reliable grounding in electrical panels.
The WAGO 2002‑433 cross‑connector expands a two‑pole terminal block into three connections, enabling flexible wiring in compact spaces. Its light grey housing and secure clamp ensure reliable, low‑profile integration.
Securely connects grounding conductors up to 2.5 mm² with a 6.2 mm wide green‑yellow terminal block, featuring a quick‑release clamp and corrosion‑resistant metal body for reliable industrial use.
Miniature circuit breaker with 3 poles and 32A current rating, providing automatic switching for safe and reliable electrical connections.
Miniature circuit breaker with 3 poles and 25A rating, providing reliable protection against overcurrent.
Miniature circuit breaker with 3 poles and 16A current rating, providing reliable protection.
Compact Siemens 5SY6316‑6 miniature circuit breaker delivers 16 A protection on three poles with a 6 kA breaking capacity, featuring a Type B curve and integrated neutral switching for reliable overload and short‑circuit safety in industrial settings.
Compact 32A single‑pole circuit breaker with Char‑B curve, rated for 230/400 V and 6 kA interrupting capacity. It features a DIN rail mount, IP20 protection, and reliable overload protection in a small footprint.
Compact 25 A, single‑pole miniature circuit breaker with a 6 kA interrupting capacity. Char‑B design delivers reliable overload and short‑circuit protection for residential or commercial wiring, featuring quick reset.
The HAGER MBN125 is a miniature circuit breaker with a rating of 1 pole, 6kA, and a characteristic of B. It has a current rating of 25A and is designed for use in electrical panels with a width of 1 module.
Bright yellow W-Series cross‑connector links four terminal block pins, enabling compact cable routing with secure Klippon® Connect clamps. Ideal for high‑current 41 A circuits, it offers robust, low‑profile connectivity.
This 3‑pole cross connector links 2.5 mm² terminals, rated 32 A, with a compact screw‑type housing for DIN rail systems. Its yellow body and robust metal contacts ensure reliable signal transfer.
Securely connect up to 2.5 mm conductors with this orange WAGO feed‑through block. Rated 24A, single pole, 5 mm pitch, 0.08–2.5 mm wire size, ideal for compact electronic assemblies.
Securely connect two conductors up to 2.5 mm² with this blue WAGO 280‑904 feed‑through terminal block, rated for 24 A and featuring a spring‑loaded clamp for quick, reliable attachment in compact spaces.
Three‑pole selective mains circuit breaker, 40 A with E‑characteristic, 690 V isolation voltage, IP20 protection, no neutral conductor, perfect fit for busbar QuickConnect systems.
A compact grey feed‑through terminal block with a 5 mm slot, rated for 24 A and supporting three conductors up to 2.5 mm², ideal for secure, low‑profile connections on DIN rails or panels.
A robust, insulated two‑pole cross‑connector that bridges a terminal block for up to six wires, enabling compact, secure connections in electrical panels while maintaining low noise and high reliability.
Ground terminal block for 2‑wire connections, rated at 2.5 mm², featuring a green‑yellow color code. Provides secure, low‑resistance grounding with a compact, one‑pole design and feed‑through capability.
Securely connect up to four conductors up to 2.5 mm² with this green, flange‑mounted terminal strip. Its single‑pole design offers reliable contact and easy installation on DIN rails or panels.
Digitus DN-93831 Face Plate for Multimedia / Keystone Modules, Empty Socket for 2 x Keystone Modules
DIGITUS DN-93831 is an empty socket with front panel designed to hold two keystone modules. It can accommodate RJ45 data outlets and comes in white color.
A robust blue feed-through terminal block with 18.5 mm spacing, rated for 150 A and UL 94 V0 flame resistance, featuring side‑mounted connections and two clamps per single layer for reliable high-current wiring.