Electrical installation
Suggestions for Electrical installation
Level Heat gun Hole saw Wire nut Cable lug Cable tie Drill bit Fish tape Cable clip Multimeter Nut driver Wire gauge Cable clamp GFCI tester Screwdriver Stud finder Wire cutter Cable cutter Cable puller Conduit body Hammer drill Tape measure Crimping tool Torque wrench Utility knife Wire stripper Cable stripper Circuit tester Conduit bender Conduit cutter Electrical box Soldering iron Terminal block Voltage tester Wire connector Bosch drill bit Conduit fitting Crimp connector Grounding clamp Milwaukee drill
Securely connect up to three grounding conductors with the PT 10‑TWIN‑PE ground terminal block, featuring a 10.2 mm wide push‑in design for quick installation and reliable continuity in green‑yellow housings.
A durable ground terminal block with a 5.2‑mm width and 100.9‑mm height, operating from –60 to +105 °C and rated at 400 V, designed for secure protection conductor connections in industrial setups.
Flush‑mounted black plastic junction box, 60 mm diameter and 66 mm depth, holds up to four screw domes for secure device connections. The IP2X rating protects against dust while remaining lightweight and easy to install in walls.
A robust single‑pole circuit breaker rated at 35 A, designed for 230–400 V mains with an E‑characteristic trip curve and 690 V isolation. It features IP20 protection, no neutral switching, and is ideal for busbar or QuickConnect installations.
A compact hollow wall junction box with a 68 mm diameter opening and 47 mm depth, designed for ceiling light connections. It features M5 threaded screws for secure mounting, IP3X protection, and is suitable for 20 mm pipe diameters.
LogiLink Power cord extension, indoor use, with 1 pass-through socket, 3.00m long, and available in white color.
LogiLink Adjustable Stripper Tool - Removes insulation from fiber optic, coaxial, and copper cables up to 3.2mm in diameter.
A bright orange, 1 mm thick end and partition plate for WAGO terminal blocks, designed for direct mounting. It provides a clean separation between terminals, ensuring secure cable management and easy maintenance in compact electrical panels.
A flush‑mounted 95 mm round cover with a robust spring lock keeps boxes or circuit boards securely closed, offering a tidy, tamper‑resistant finish without the need for screws.
Latching relay S12-100-12V by Eltako. 12V AC, impulse switch with 1 Normally Open contact. Electromechanical impulse switch mounted on DIN rail, rated for 10A and 2300W.
A robust, recessed Siemens SIE 5UB1927 offers a 10/16 A, 250 V grounded socket with a durable metal shell and secure locking mechanism for reliable industrial use. Its sleek design fits seamlessly into panelboards or wall mounts while providing easy access to the protected contact point.
Sleek titanium white frame, 80 × 80 mm, glossy finish, IP20 and halogen‑free thermoplastic construction, designed for direct wall mounting of a single‑gang switch in either horizontal or vertical orientation.
Durable Siemens Delta i‑system Schuko outlet delivers 10–16 A at 250 V with secure earthing, robust metal housing and easy installation for reliable household or commercial use.
Flush-mounted series switch with device insert, featuring a double switch mechanism and 10A 250V rating.
Siemens 3NA3824 NH fuse: 000 size, 80 A, 500 V AC, 250 V AC rating, 3 pieces. Low voltage HRC fuse for 3NA3824.
A sleek, surface‑mounted switch in dark grey or light grey, IP44 rated for heating circuits up to 10 A at 250 V. It features a polished plastic body with optional LED illumination and a simple lever/press action, mounted by screws for easy installation.
Siemens Delta pushbutton device insert (5TD2116) provides flush fitment with continuous light for easy identification and control in electrical systems.
A sleek titanium‑white Siemens DELTA i-system socket delivers reliable 10/16 A power with a built‑in earthing contact, offering robust protection and easy installation for everyday use.
A robust two‑pin Schuko receptacle with an IP44 rating, featuring a durable blue thermoplastic body that protects against dust and splashes. The integrated earth contact ensures safety, while the compact design allows straightforward wall mounting in both residential and light commercial settings.
The UT 6-PE is a green and yellow ground terminal block for 0.2 to 6mm² conductors, with a one-piece design and 8.2mm spacing between terminals. It is suitable for various applications and provides reliable protection against electrical hazards.
Compact blue feed‑through terminal block with 8.2 mm bore, rated for up to 41 A and compatible with 0.2–10 mm² conductors, offering secure screw clamping and easy cable routing in industrial panels.
The UT 6 feed-through terminal block features an 8.2 mm pitch and can handle up to 41 A, making it suitable for wiring ranging from 0.2 mm² to 6 mm² in industrial control applications.
Blue feed‑through terminal block with a 6.2 mm bore, rated for 32 A and accommodating conductors from 0.14 mm² to 6 mm². It features a screw clamp for secure attachment, making it ideal for DIN rail installations and reliable signal routing.
Green push button designed for distribution boards, featuring a non‑latching action with one normally open and one normally closed contact, rated at 20 A, compact size for easy series installation, ensuring reliable control in industrial panels.
Compact 1‑pole Siemens 5SY6132‑7 delivers a 32 A rating with Char‑C curve protection for motor starts, 6 kA breaking capacity, DIN rail mountable and reliable for residential or industrial use.
Siemens 5SY6116-7 16 A 230 V, 400 V miniature circuit breaker with 1 pole and 6kA fault current rating.
A compact 5‑pin cross‑connector designed for ST1.5 terminal blocks, it offers a secure fixed bridge that links two sets of terminals without the need for additional tools. The robust construction ensures reliable signal continuity and easy integration into existing wiring harnesses.
Vertical two‑port Schuko outlet in matte alpine white, IP44 splash protection, thermoplastic housing with a fold‑down cover and secure earth contact, perfect for wall‑mounted use.
Secure two conductors up to 6 mm² with this grey WAGO feed‑through terminal block, rated 41 A and 7.5 mm width, ideal for DIN rail installations in compact spaces.
The Busch‑Jaeger 20 EWN‑54 offers a reliable Schuko connection featuring an earth pin, a protective hinged cover, and a built‑in label field for clear identification. Its sleek white finish and compact size fit seamlessly into any wall-mounted setup.
A sleek matte plastic combination with a rocker switch and two Schuko sockets, IP44 rated for damp areas, 250 V capacity, 74 mm wide, 55 mm deep, mounted by screw, ideal for modern wall panels.